How could I guess a checksum algorithm?
Let's assume that I have some packets with a 16-bit checksum at the end. I would like to guess which checksum algorithm is used.
For a start, from dump data I can see that one byte change in the packet's payload totally changes the checksum, so I can assume that it isn't some kind of simple XOR or sum.
Then I tried several variations of CRC16, but without much luck.
This question might be more biased towards cryptography, but I'm really interested in any easy to understand statistical tools to find out which CRC this might be. I might even turn to drawing different CRC algorithms if everything else fails.
Backgroud story: I have serial RFID protocol with some kind of checksum. I can replay messages without problem, and interpret results (without checksum check), but I can't send modified packets because device drops them on the floor.
Using existing software, I can change payload of RFID chip. However, unique serial number is immutable, so I don't have ability to check every possible combination. Allthough I could generate dumps of values incrementing by one, but not enough to make exhaustive search applicable to this problem.
dump files with data are available if question itself isn't enough :-)
Need reference documentation? A PAINLESS GUIDE TO CRC ERROR DETECTION ALGORITHMS is great reference which I found after asking question here.
In the end, after very helpful hint in accepted answer than it's CCITT, I used this CRC calculator, and xored generated checksum with known checksum to get 0xffff which led me to conclusion that final xor is 0xffff instread of CCITT's 0x0000.
Answer
There are a number of variables to consider for a CRC:
Polynomial
No of bits (16 or 32)
Normal (LSB first) or Reverse (MSB first)
Initial value
How the final value is manipulated (e.g. subtracted from 0xffff), or is a constant value
Typical CRCs:
LRC: Polynomial=0x81; 8 bits; Normal; Initial=0; Final=as calculated
CRC16: Polynomial=0xa001; 16 bits; Normal; Initial=0; Final=as calculated
CCITT: Polynomial=0x1021; 16 bits; reverse; Initial=0xffff; Final=0x1d0f
Xmodem: Polynomial=0x1021; 16 bits; reverse; Initial=0; Final=0x1d0f
CRC32: Polynomial=0xebd88320; 32 bits; Normal; Initial=0xffffffff; Final=inverted value
ZIP32: Polynomial=0x04c11db7; 32 bits; Normal; Initial=0xffffffff; Final=as calculated
The first thing to do is to get some samples by changing say the last byte. This will assist you to figure out the number of bytes in the CRC.
Is this a "homemade" algorithm. In this case it may take some time. Otherwise try the standard algorithms.
Try changing either the msb or the lsb of the last byte, and see how this changes the CRC. This will give an indication of the direction.
To make it more difficult, there are implementations that manipulate the CRC so that it will not affect the communications medium (protocol).
From your comment about RFID, it implies that the CRC is communications related. Usually CRC16 is used for communications, though CCITT is also used on some systems.
On the other hand, if this is UHF RFID tagging, then there are a few CRC schemes - a 5 bit one and some 16 bit ones. These are documented in the ISO standards and the IPX data sheets.
IPX: Polynomial=0x8005; 16 bits; Reverse; Initial=0xffff; Final=as calculated
ISO 18000-6B: Polynomial=0x1021; 16 bits; Reverse; Initial=0xffff; Final=as calculated
ISO 18000-6C: Polynomial=0x1021; 16 bits; Reverse; Initial=0xffff; Final=as calculated
Data must be padded with zeroes to make a multiple of 8 bits
ISO CRC5: Polynomial=custom; 5 bits; Reverse; Initial=0x9; Final=shifted left by 3 bits
Data must be padded with zeroes to make a multiple of 8 bits
EPC class 1: Polynomial=custom 0x1021; 16 bits; Reverse; Initial=0xffff; Final=post processing of 16 zero bits
Here is your answer!!!!
Having worked through your logs, the CRC is the CCITT one. The first byte 0xd6 is excluded from the CRC.