arm-none-eabi-gdb and openocd: Malformed response to offset query, qOffsets?
I am attempting to use GDB to debug a Stellaris LM3S8962 Evaluation board using OpenOCD and the GNU ARM toolchain (installed with MacPorts), whenever I set the remote target in GDB it always returns "Malfomred response to offset query, qOffsets". Any ideas on what could be going wrong? Is there anything that I am missing?
[bcochran@narada arm]$ arm-none-eabi-gdb
GNU gdb (GDB) 7.3
Copyright (C) 2011 Free Software Foundation, Inc.
License GPLv3+: GNU GPL version 3 or later <http://gnu.org/licenses/gpl.html>
This is free software: you are free to change and redistribute it.
There is NO WARRANTY, to the extent permitted by law. Type "show copying"
and "show warranty" for details.
This GDB was configured as "--host=x86_64-apple-darwin10.7.0 --target=arm-none-eabi".
For bug reporting instructions, please see:
<http://www.gnu.org/software/gdb/bugs/>.
(gdb) set remotebaud 115200
(gdb) set debug remote 1
(gdb) file ~/dev/eclipse_workspace/hello_world_arm/bin/main.axf
Reading symbols from /Users/bcochran/dev/eclipse_workspace/hello_world_arm/bin/main.axf...(no debugging symbols found)...done.
(gdb) target remote localhost:4444
Remote debugging using localhost:4444
Sending packet: $qSupported:qRelocInsn+#9a...putpkt: Junk: {{}~Open On
Nak
Sending packet: $qSupported:qRelocInsn+#9a...putpkt: Junk: Chip Debugger
>
Ack
Packet received: qSupported:qRelocInsn+
Packet qSupported (supported-packets) is supported
...
Packet qAttached (query-attached) is supported
Sending packet: $qOffsets#4b...Ack
Packet received: qOffsets
Malformed response to offset query, qOffsets
Here is the openocd output... as soon as the malformed response comes across openocd drops the telnet connection...
[bcochran@narada bin]$ openocd -f ../openocd/luminary.cfg -f ../openocd/stellaris.cfg
Open On-Chip Debugger 0.6.0-dev-00014-g827057f (2011-08-09-22:02)
Licensed under GNU GPL v2
For bug reports, read
http://openocd.berlios.de/doc/doxygen/bugs.html
Info : only one transport option; autoselect 'jtag'
500 kHz
Info : clock speed 500 kHz
Info : JTAG tap: lm3s.cpu tap/device found: 0x3ba00477 (mfg: 0x23b, part: 0xba00, ver: 0x3)
Info : lm3s.cpu: hardware has 6 breakpoints, 4 watchpoints
Info : accepting 'telnet' connection from 4444
Error: error during read: Connection reset by peer
Info : dropped 'telnet' connection
Here are the version outputs of my arm-none-eabi-* toolchain...
[bcochran@narada tcl]$ arm-none-eabi-gcc -v
Using built-in specs.
COLLECT_GCC=arm-none-eabi-gcc
COLLECT_LTO_WRAPPER=/opt/local/libexec/gcc/arm-none-eabi/4.6.1/lto-wrapper
Target: arm-none-eabi
Configured with: ../gcc-4.6.1/configure --prefix=/opt/local --target=arm-none-eabi --enable-languages=c,objc,c++,obj-c++ --infodir=/opt/local/share/info --mandir=/opt/local/share/man --datarootdir=/opt/local/share/arm-none-eabi-gcc --with-system-zlib --disable-nls --with-gmp=/opt/local --with-mpfr=/opt/local --with-mpc=/opt/local --enable-stage1-checking --enable-multilib --with-newlib --enable-interwork
Thread model: single
gcc version 4.6.1 (GCC)
[bcochran@narada tcl]$ arm-none-eabi-gdb -v
GNU gdb (GDB) 7.3
Copyright (C) 2011 Free Software Foundation, Inc.
License GPLv3+: GNU GPL version 3 or later <http://gnu.org/licenses/gpl.html>
This is free software: you are free to change and redistribute it.
There is NO WARRANTY, to the extent permitted by law. Type "show copying"
and "show warranty" for details.
This GDB was configured as "--host=x86_64-apple-darwin10.7.0 --target=arm-none-eabi".
For bug reporting instructions, please see:
<http://www.gnu.org/software/gdb/bugs/>.
I am able to compile using the toolchain, and flash the resultant .bin file using OpenOCD. I have been unable to find a solution to the "malformed response" issue just by searching the web.
Thanks in advance for any advice or assistance!
UPDATES
Thanks to answers from @turbo-j and @guy-sirton, I was able to progress a bit further... The most helpful thus far was that I was indeed using the wrong port (4444 instead of 3333) but now I am getting the following whether I add -c "init" -c "halt" -c "reset halt" to my openocd command string or not:
(gdb) target remote localhost:3333
Remote debugging using localhost:3333
Remote 'g' packet reply is too long: 0080004000000000040000220f0000002833405451332abc009600a4d2b86092c0c118c03040d6f0284dbb93204b40c2000000000c010020ffffffff550400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000020000001
(this is right after the qOffsets req/resp, which now passes)
On the OpenOCD side:
Info : accepting 'gdb' connection from 3333
Warn : acknowledgment received, but no packet pending
Info : dropped 'gdb' connection
With sometimes a undefined debug reason 6 - target needs reset on the OpenOCD console...not sure what is going on now but it seems closer to functioning
UPDATES 2
It seems if I do not load the file 'main.axf' or 'main.o' I do not run into the Remote 'g' packet reply is too long but I get no symbols... I've noticed other websites deal primarily with the .elf extension. What is the difference? I'm using the "Hello World" example from StellarisWare which it generates main.axf, main.bin (flash writes and runs fine), main.d, main.o from the make command. Something odd about my Makefile?
Answer
Here is a patch like what @athquad mentioned. See his answer for more information. Thanks to him for efficiently pointing me at the right spot, and great shame indeed for offering a patch without providing it. :-P
Patch was made against openocd commit 631b80fd0835055bb385314f569f589b99d7441d
To use: (./configure options depend on jtag hardware)
git clone git://git.code.sf.net/p/openocd/code openocd
cd openocd
patch -p1 < /path/to/patch/file
./bootstrap
./configure --enable-maintainer-mode --enable-ft2232_libftdi
nice make && sudo make install